| |
Reset
ip2000 / 3000
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4
times.
7. Press the Power button and the printer should turn off,
if not,
press the Power button once more.
8. Your printer should respond as normal..
Reset MP110
1)Enter SERVICE MODE By pressing Menu-Scan-Copy-Scan
2) Enter NVRAM by pressing-- or ---> then OK
3) Enter CMY ink level by pressing <--- or ---> then OK
4) Select 1 by pressing<--- or ---> then OK
5) Enter K ink level by pressing--> then OK
6) select 1 by pressing<--- or ---> then OK
7) Press reset ( design: // )
8) SERVICE MENU COUNTER ACCESS
PRINT PAGE COUNT SCAN PAGE COUNT
-------------------------------------------------------------
Canon PIXMA iP1000
Waste Ink Counter Reset Manual for Service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (LED) should be green.
4. Press and release the RESUME button , the indicator (LED)
should be orange.
5. Press and release the RESUME button again, the indicator
(LED) should be green.
6. Release both buttons.
-------------------------------------------------------------
Canon PIXMA iP1500
Waste Ink Counter Reset. Manual for Service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (LED) should be green.
4. Press and release the RESUME button , the indicator (LED)
should be orange.
5. Press and release the RESUME button again, the indicator
(LED) should be green
6. Release both buttons
-------------------------------------------------------------
Canon i320, i255
Waste Ink Counter Reset.
Step 1 : Manual Temporary
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
or Step 1: Manual Temporary
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (LED) should be green.
4. Press and release the RESUME button , the indicator (LED)
should be orange.
5. Press and release the RESUME button again, the indicator
(LED) should be green.
6. Release both buttons.
Step 2 : Software for Permanent
1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.
Remark "After service mode use software for permanent reset"
------------------------------------------------------------
Canon GENERIC "S" SERIES RESET CODE
Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold
the POWER button.
(3) Release the RESUME button, Next press and release the
RESUME button two(2) more times in
succession. Note: you are still holding the POWER button).
The printer's carriage will "reset"
or move momentarily. If the above was properly performed the
printer will enter the
"Service Mode".
(4) Press the RESUME button 4 times, this will select the
clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor
check.
2. EPROM - Info printout.
3. EPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point
- However it is best leave them unaltered - You have been
warned!)
After selecting the desired mode (eg. 4), press the POWER
button to "set" the change, and return to the top of the
function selection menu. Press the POWER button again to
restart the printer.
-----------------------------------------------------------
Canon i850, i950, S600
Start with the printer OFF
1. Hold down RESUME and then hold down POWER
2. release RESUME
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses - light color - function
Number of presses - light color - function
0 presses - green - Test print (or exit service mode on
i960)
1 press - orange - EPROM info print (plus grid nozzle
diagnostic on i960)
2 presses - green - EPROM initialize
3 presses - orange - Reset waste ink counter
----------------------------------------------------------
Canon S450 Printer
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper
will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5. Release Power button
6: When the indicator lights steady, press RESUME three(3)
times. The indicator should be orange.
7: Press Power to set data
----------------------------------------------------------
Canon BJC 1000 Series
1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the
RESUME .
6: Press and HOLD RESUME for two seconds or more and release
it.
7: Press and HOLD RESUME for two seconds or more and release
it.
8: Unplug AC Power Cord to set data.
----------------------------------------------------------
Canon BJC-2000 BJC-2100 Series
1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Close Front access panel
3: Hold down the RESUME/RESET button and plug in the AC
power cord
4: Release RESUME/RESET after plugging in the AC Power cord.
5: Press the RESUME/RESET once within 5 seconds and release
the RESUME/RESET .
6: Press and HOLD RESUME/RESET for two seconds or more and
release it.
7: Press and HOLD RESUME/RESET for two seconds or more and
release it.
8: Unplug AC Power Cord to set data.
----------------------------------------------------------
Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265
Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650
Unplug Power Cord
Hold POWER and RESUME buttons
Plug in Power Cord
Release buttons
Open front door of printer
Hold the CARTRIDGE and RESUME buttons
Press POWER
Release all buttons after the beeps
Press CARTRIDGE once
Press RESUME
----------------------------------------------------------
Canon BJC-5000
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator
will start blinking.
3: While the indicator is blinking , Press RESUME twice then
Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME
four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator
will start blinking.
3: While the indicator is blinking , Press RESUME twice then
Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME
two(2)times. The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until
the printer plays a melody of beeps.
----------------------------------------------------------
Canon BJC-5100
Self Test
Switch Printer off. Hold Power for 1 beep.
Waste Counter Reset
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator
will start blinking.
3: While the indicator is blinking , Press RESUME twice then
Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME
four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator
will start blinking.
3: While the indicator is blinking , Press RESUME twice then
Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME
two(2)times. The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until
the printer plays a melody of beeps.
----------------------------------------------------------
Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300
F600 F620
Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper
will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three(3)
times. The indicator should be orange.
6: Press Power to set data
-----------------------------------------------------------
Canon BJC-600 BJC-600e BJC-610 BJC-620
1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons
3: Plug in Power Cord
4: Release after the beeps
-----------------------------------------------------------
Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70
1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord
4: Release buttons after the printers starts up
5: Hold CARTRIDGE and RESUME
6: Press POWER
7: Release all buttons after the beeps
8: Press CARTRIDGE 16 times
9: Press RESUME
10: Unplug the Power cord
-----------------------------------------------------------
Canon BJ-30 BJC-35v BJC-70
F14 Error Reset
1: Unplug adapter
2: Hold POWER
3: Plug in ADAPTER
4: Release POWER after printer starts
5: Hold FF and MENU and press POWER
6: Release after beeps
7: Press <> Cartridge until 1A is displayed
8: Press ONLINE
9: Press POWER to shutoff printer
10: Unplug printer then re-plug printer
----------------------------------------------------------
Canon BJ F900, F890, F700, F500, S900, S820, S750 and
S520
Turn off the printer.
Press and hold the RESUME button, then press and hold the
POWER button.
Release the RESUME button, then press and release the RESUME
button two more times in succession. (you're still holding
the POWER button during this). The printer mechanics will
move momentarily.
You are now in Service mode.
Pressing the RESUME key will select a function; for example,
pressing RESUME 4 times will select the clear waste ink
counter function. The lamp will alternate color with each
key press.
1. service/factory test printout, including ink sensor check
2. EPROM info printout
3. EPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this-
leave this alone)
After selecting mode, press the POWER button to commit the
change, and return to the top of the function selection
menu. Pressing the POWER button again turns off the printer
for a restart
----------------------------------------------------------
Canon S9000, S300, S400, i550, i560, i850, i860, i865,
i9100, i9950, PIXMA IP3000
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4
times.
7. Press the Power button and the printer should turn off,
if not, press the Power button once more.
8. Your printer should respond as normal.
----------------------------------------------------------
Canon S900, S820, S750, S520
1. Turn off the printer.
2. Press and hold the RESUME button, then press and hold the
POWER button.
3. While still holding the POWER button, Release the RESUME
button, then press and release the RESUME button two more
times in succession.
4. The printer mechanics will move momentarily. You are now
in Service mode. Release the Power Button.
5. Pressing the RESUME key will select a function; for
example, pressing RESUME 4 times will select the clear waste
ink counter function. The lamp will alternate color with
each key press.
1. Service/factory test printout, including ink sensor check
2. EPROM info printout
3. EPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this-
leave this alone)
6. After selecting mode, press the POWER button to commit
the change, and return to the top of the function selection
menu. Pressing the POWER button again turns off the printer
for a restart.
---------------------------------------------------------
Canon S9000
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4
times.
7. Press the Power button and the printer should turn off,
if not, press the Power button once more.
8. Your printer should respond as normal.
---------------------------------------------------------
Canon MPC190
Reset Waste Ink
1) Enter SERVICE MODE.
By pressing Menu Copy Scan Copy Copy
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [Set] key.
7) Press the [Stop/Reset] key (returning to the state of
3)), and then press the [ON/OFF] key.
------------------------------------------------------------------
The instructions provided have
not been tested by us and so therefore the user takes full
responsibility of what he or she does with their printer. If
you are in doubt as to the credibility of these instructions
then please contact a Canon service representative and
verify the information yourself. |
|
